MATERIALS OR COMPUTER PERIPHERAL EQUIPMENT FOR CLEANING

MATERIALS OR COMPUTER PERIPHERAL EQUIPMENT FOR CLEANING

 
a) Vacuum Cleaner Mini


           Mini vacuum cleaner is almost the same with a brush used to remove dust. But the vacuum cleaner easier and cleaner. At the end of the mini vacuum cleaner equipped with a brush sizes vary widely intended to adjust the narrowness of the corners on the component. This tool is ideal to use for cleaning the circuit on the mainboard and in the corners casingkomputer.

 b) Fabrics Dry, Tissue and Fluid Cleansing


         Dry cloth or paper towels used to clean liquid which may result softdrink, ink or rain water that is fresh or not dry. Liquid manure is very dangerous if not promptly cleaned up because of this kind of dirt can deliver currents that could lead to a short circuit or fatal damage to the PC component. While the cleaning fluid used to clean stains or dirt that has dried up like a splash of ink printer.



 c) Brush


          Brush is the equipment used to clean dust or insect nests. In addition the brush was also used to clean dust that closes at fentilasi casing. Brush can also use to clean the heatsink fins on the motherboard and processor.

 d) Disk Cleaner


          Disk cleaner is used to clean the head of the diskdrive of the influence of dust or dirt on the floppy drive head. Disk cleaner is composed of cleaning fluid and floopydisk that piringannya replaced with tissue paper.

 e) CD Cleaner


        CD cleaner same principle works with disk cleaner is to rub the dusty or dirty with cleaning fluid by utilizing lap. Different cd disk cleaner cleaner with only lies in the shape that is on a CD cleaner using a small brush or fins mounted on the disk.

 f) Screwdriver

       Screwdriver is essential equipment for computer technicians, because with this tool technician is able to open and release the components in the PC.

 g) Tang


      Kinds of pliers for the purposes of technicians to perform maintenance of PC components is pliers combination pliers and shark. Tang shark is widely used to hold the head of a small screw or jumper. As for the combination pliers used to cut wires and other purposes.

  TAKING CARE PERIPHERAL
To carry out the cleaning of components on peripherals must go through certain means or procedures. Procedures that must be taken adapted to the types of peripherals and dirt that is on the peripherals.
The following cleanup steps peripheral components:
a) Keyboard

      The procedure to clean the keyboard from liquid manure:
• Use a dry cloth or tissue to clean the liquid manure.
• Clean the keyboard keys slowly
Cleaning Procedure keyboard from dust and dirt:
Use a small brush or a vacuum cleaner with a brush tip is small and cramped.
So that dust or dirt can be easily sucked.
b) Mouse
The procedure to clean the mouse from dust:
• Use a cloth and cleanser dirt or dust on the mouse ball and shaft.
• Clean the ball slowly and slowly the mouse wheel
c) Monitor
Monitor cleaning procedure:
• use a small brush or a vacuum cleaner with the tip of a small brush to clean the dust.
• To clean the monitor from liquid manure that sticks to the screen, use a cleanser and then wipe with a dry cloth. Especially at the corner of the screen.
d) Printer
Printer maintenance procedures:
• Use a damp cloth to clean the printer. Do not use flammable liquids such as alcohol, gasoline or paint thinner. When flammable liquids associated with electrical components inside the printer, it can result in fire or short circuit. Always unplug the printer from the outlet when the printer is cleaned.
• Do not put the printer in a place that is unstable or prone to vibration or
shock. The printer may fall and be damaged.
• Do not put the printer in a humid or dusty, exposed to direct
sun or near a heat source or flame.
III. Checking the results of treatment of peripheral
Tool used weeks to check the peripherals:
a) Device Manager

       Device Manager is used to determine the overall situation. properties, kemudianUntuk display: right click on my computer device manager. From the Device Manager tab dapatpilih hardware known to all the hardware installed on the PC. This tool can be used to disable / enable hardware installed and to uninstall drivers and driver updates. Device manager can also provide information on whether the drivers for the peripherals are installed properly or not. If peripherals are not installed properly, then there will be the symbol "!" On these peripherals.
b) System Information
System information is used to find out information of the hardware. For Systema system toolsàacessoriesà programàmemanggil this tool click start information. We will get to see as shown below.
InformationTool System information Display System is equipped with a search function that serves to facilitate the search for the components inside the computer. In addition this tool is also equipped with facilities capable of being used to diagnose network, hardware and file system.
c) Direct X

      DirectX is the default Windows tool used to diagnose all hardware associated with graphics, network and multimedia. DirectX Tool can also be called from the tool system information.
Display DirectX tool consists of three parts: Device, driver, feature and note. With DirextX tool can know whether there is any trouble in the attached peripherals. This tool is very easy to use to test the ability of the monitor resolution, 3D support capabilities.
See in the picture above shows that the problem can not be found
on the periphery of the display.
d) Printer Tool

     Tool used for printer maintenance can use the software from the vendor. In this report using the printer with the brand Cannon S200Spx. Here are the tools used to diagnose printer.
• Cleaning and deep cleaning is used to clean the head of the ink which inhibits needle printer head.
• Nozzle check is used to check the pattern of the printer head, this method is used if the pattern of the printer has a problem.
• Print Head alinggment used to fix the position of the printer head when the irregularities.
• Ink Counter Reset, used to reset the ink indicator so that the full-back. This tool is used when it is done charging ink.
• Low Ink Warning Setting used to display a message or a warning if the conditions of the ink is low.
• Customs operation mode setting is used to set the printer in a long time at least wait until the ink is dry. It is intended to set the speed for each print the sheet if the ink drying time is brought forward.